How to Rest Whirlpool Refrigerator

How to Reset Whirlpool Refrigerator?

There are times when you may need to reset your Whirlpool refrigerator. Perhaps the water filter needs to be replaced and the “change filter” light is on, or maybe the freezer isn’t getting cold enough. Whatever the reason, it’s important to know how to reset your Whirlpool refrigerator in case of a problem.

Is There a Reset Button on Whirlpool Refrigerator?

If your Whirlpool refrigerator isn’t working properly, you may be wondering if there’s a simple reset button that you can use to get it back up and running again. Unfortunately, there is no Reset button on the new Whirlpool refrigerators.

How to Reset a Whirlpool Refrigerator

Follow the steps below to reset the Whirlpool refrigerator:

Step 1: Unplug the refrigerator

To begin with, turn off your Whirlpool cooler from the power attachment or the main switch.

Doing this will remove the power supply from your machine, permitting your refrigerator to:

  • Reboot.
  • Invigorate its framework.
  • Fix errors and blunders.

In some houses, there is a principal circuit breaker in private houses that have a particular switch for coolers. In that case, search for a solitary electrical switch in your kitchen.

Step 2: Wait for 8 to 10 minutes

In the wake of turning off your refrigerator, sit tight for around 8 to 10 minutes.

This is important to guarantee that the power supply in your machine is totally cut off.

Remember, whenever you turn off any machine or contraption, a specific measure of force supply stays in the unit. That excess power supply will keep on running in its system until it runs out. Which can require a few seconds or minutes to wrap up.

Step 3: Replug the refrigerator

Then, Power On your Whirlpool refrigerator by replugging it or turning ON its electrical switch.

In the wake of turning it ON, you ought to hear a humming sound which demonstrates that its fan and engine are running.

Note: This progression finishes the essential resetting process.

Step 4: Press and hold the LOCK and FILTER buttons

Generally, the fridge’s cooling capacity will reactivate too whenever you turn ON the unit.

On the off chance that not, then, at that point, you need to physically direct it back toward yourself.

To do that:

  • Find the control board.
  • Press the LOCK and the FILTER fastens all the while.
  • Hold the buttons for 3 seconds.
  • Then, at that point, discharge.
  • To check whether it’s effective, check whether the vents inside the cooler are delivering cool air.

If it doesn’t, have a go at rehashing a similar cycle.

Note: The control board is situated at the door or inside the unit, contingent on your fridge model.

The control board inside the cooler unit is alluded to as “Control W10503278.”

Step 5: Check the control panel’s functionality

This is the ideal opportunity for you to check whether the control board is working immaculately.

Consider your Whirlpool ice chest control board “failing” if:

  • It’s blazing lights.
  • It’s making a humming sound.
  • All or a portion of its buttons are lethargic.

Assuming any of these signs are as yet present in your unit, you Leap to step #9.

Step 6: Locate the door switch

Open the fridge door.

Then, at that point, contingent on your refrigerator model, search for 1 or 2 entryway switches.

The Whirlpool fridge entryway switch is commonly hued white. Furthermore, is situated on one side of the unit where the refrigerator entryway is joined to. Basically, it’s just like a regular light switch in the house.

Great to be aware: The entryway switch switches OFF the light and controls different capacities whenever you’ve shut its entryway.

Step 7: Press the door switch and temperature button 

Presently, press the entryway switch and temperature in addition to the (+) button multiple times in 10 seconds or less.

Whenever you’ve delivered the button and entryway switch, the cooler board will show an “S.”

Also, the ice chest board will show an “E” to demonstrate that a reset cycle is finished.

Step 8: Press the temperature plus (+) button again

From that point forward, press the temperature plus (+) button once more.

Doing this will hinder your Whirlpool fridge to “administration mode.”

When done, the cooler board will show the number “1” and then clear. That shows that the reset cycle is finished and effective.

In the event that it actually doesn’t work, continue to step #9.

Step 9: Contact Whirlpool support for service

Assuming all things fall flat, contact Whirlpool support for help or administration.

Rather than attempting other investigating strategies, request help from Whirlpool experts. This will ensure that the problem is fixed. Furthermore, your item guarantee won’t be void.

Prior to reaching Whirlpool support, make a point to set up the accompanying:

  • Guarantee data.
  • Request number (discretionary).
  • Whirlpool cooler model.
  • Whirlpool cooler chronic number.

The product model and serial number in Whirlpool refrigerators are situated inside the unit. To its left side or right side, contingent upon where the refrigerator entryway is appended to.

Search for a rectangular sticker, and note down your refrigerator’s model and chronic numbers.

How to reset the Whirlpool control panel?

To reset the control board of this unit, open the entryway of the refrigerator and find the entryway switches. Press the switches and the refrigerator temperature button-up multiple times in ten seconds.

Discharge the switches and button, and you will see the letter ‘s’ displayed on the board of the freezer section. The letter ‘e’ will be displayed in the cooler section.

Press the temp button of the refrigerator once. A few numbers will show on the presentation, with ‘1’ appearing on the showcase of the freezer section.

Then, at that point, assuming the presence of the cooler goes clear while the freezer shows ‘1’, the control board has been reset.

Reset only the Ice Maker

To reset the ice maker on a Whirlpool refrigerator, start by shutting off the power to the unit.

Then, locate the arm on the side of the machine that controls when it dispenses ice. Pull this arm up and set it in a horizontal position.

Next, press and hold down the “off/on” button for about 5-10 seconds until you see a light flash on and off.

This signals that your ice maker has been reset. Once you see this light flashing, you can turn the power back on to your refrigerator and let your ice maker resume normal operation as usual.

Common Whirlpool problems & their solutions

1. What to do if your refrigerator isn’t cooling properly

If your fridge isn’t cooling properly, there are a few things that you can try in order to get it back up and running again.

  • First, check to make sure that the power cord is plugged into an outlet and that the fridge is turned on.
  • Next, check to see if the door is properly sealed shut.
  • If not, try cleaning the gasket and making sure that it’s free of debris.
  • Finally, if your fridge still isn’t working, you may need to call a service technician. With proper care and maintenance, your Whirlpool refrigerator should provide you with years of trouble-free operation.

2. What to do if water isn’t coming out of the dispenser

If water isn’t coming out of the dispenser on your Whirlpool refrigerator, there are a few things you can try to resolve the issue.

First, make sure that your unit is properly connected to an appropriate water source and that the water shutoff valve is turned on. If this is already the case, try resetting your refrigerator.

If still, the water isn’t coming out of the Whirlpool refrigerator, then there may be a clog or other blockage in your water dispenser line. To diagnose and address this issue, you may need to consult with a professional repair technician who can evaluate the problem with your specific machine model.

Regardless of the cause of your problem with water dispensement, resolving it as quickly as possible will ensure that you’re able to continue using your Whirlpool refrigerator as usual.

3. How to Reset only the Water filter?

To reset the water filter on your Whirlpool refrigerator, first locate the filter on the back or side of your appliance, depending on your model.

Then press and hold the button next to the filter for at least 3 seconds to release any built-up pressure in the system.

Next, turn off your refrigerator and disconnect the power cord. Once you have disconnected the power source, wait a few minutes before proceeding with the reset process.

Finally, remove and discard any existing water from the filter cartridge, and add fresh cartridges according to manufacturer recommendations.

Once you have replaced your filtration system, simply plug in your refrigerator and turn it on to resume normal operation. With these simple steps, you can easily reset your Whirlpool refrigerator water filter and ensure the optimal performance of your appliance.

Get this Every drop by Whirlpool Ice and Water Refrigerator Filter 1 from Amazon

everydrop by Whirlpool Ice and Water Refrigerator Filter 1


We hope this guide will help you to understand the process of resetting your Whirlpool refrigerator and solving other related problems. If you have any other questions or tips regarding the Whirlpool refrigerator, feel free to leave them in the comments below!

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *