Norcold Refrigerator Reset Procedure
If your Norcold RV refrigerator isn’t working, you may need to reset it. Here we have discussed the Norcold refrigerator reset procedure with and without the button.
How to Reset a Norcold Refrigerator
Reset your NorCold refrigerator by following the steps below:
Step 1: Find the display pan
A soft reset reboots the fridge’s system, which helps it perform and cool all the more proficiently.
Not at all like other smart fridges, you can reset your unit by pressing a particular control button.
To delicate reset, find the ice chest’s display board first.
Contingent upon your cooler model, it can either be found:
- Inside the unit.
- On top of the ice chest door.
Step 2: Press and hold the “ON/OFF” button
Whenever you’ve found the display board, look for the “ON/OFF” button.
As the name infers, it turns ON and OFF the machine.
Be that as it may, you can likewise utilize it to delicate reset your unit.
To do that:
- Press the ON/OFF button.
- Hold it for around 3 seconds.
- Then, at that point, discharge.
- After this, the display board and refrigerator’s engine will shut down.
Assuming the display board is inside the unit, close the cooler door and continue to the following stage.
Step 3: Wait for 3 to 5 minutes
Actually, the delicate reset is done in the wake of pressing the ON/OFF button.
However, to guarantee a fruitful reset, let it sit for 3 to 5 minutes.
Switching OFF the cooler for a couple of moments helps its blower rest and reboot. Which further develops the cooler’s cooling capacity.
Besides, it additionally helps resolve the “no co” error code. Since this error is attached to the refrigerator’s cooling effectiveness.
Step 4: Press and hold the “ON/OFF” button once more
Once done, press and hold the ON/OFF button again for 3 seconds.
Doing this gets the refrigerator back in help.
Then, take a look at your refrigerator’s display board.
On the off chance that the “no co” error code isn’t displaying anymore, that implies that the issue has been settled. Congrats!
However, on the off chance that it stays, hard reset your refrigerator’s power board.
How to Hard Reset a Norcold Refrigerator?
Step 1: Turn OFF the unit
Assuming you’ve arrived at this progression, it’s either that:
The soft reset didn’t work.
Your refrigerator has displayed a “no co” error two times or more.
Notwithstanding this, your best arrangement is to hard reset the power leading group of your Norcold fridge.
Caution: This reset interaction is precarious and includes separating wires. Along these lines, possibly do this if required.
Besides, doing this may likewise void your product warranty.
That being said, hard reset your Norcold ice chest provided that:
You’re an expert professional.
Your ice chest guarantee has been terminated.
To begin the hard-reset process, switch OFF your refrigerator.
You can do that by squeezing and holding the ON/OFF button on the display board.
Step 2: Disconnect wires from the power board
Separate Certain Wires From The Power Board
Then, take out your cooler to get to its backboard. Or on the other hand, in the event that you can’t haul it out, access it from an external perspective of your RV.
Then, at that point, read the port names and find the accompanying wires:
- 12 Vdc positive and negative wires.
- AC power rope.
- Solenoid gas valve wires.
- Flash/sense anode get-together wires.
- Whenever you’ve found them, detach the wires in the accompanying request referenced previously.
Remove the wires from the rear of the refrigerator by cautiously taking out their attachments.
Step 3: Unscrew the front cover of the power board
Then, find the power board and remove its cover.
The panelboard cover is typically dark black, rectangular, and situated on the left side.
To eliminate the power board cover:
- Find at least 4 screws around it.
- Remove them utilizing a screwdriver.
- Put away the cover and the screws.
Pro Tip: You can likewise get a little magnet to try not to lose the screws.
Step 4: Reconnect 12 Vdc positive and negative wires
Older and newer models follow a slightly different procedure. Also, you can figure out which one applies to your unit by its serial number.
See the aide underneath for the following stage.
For models with serial number 832171 or higher reconnect the 12 Vdc positive and negative wires.
For models with serial number 832170 or lower reconnect the wires in the following order:
- Spark/sense electrode assembly wire
- Solenoid gas valve wires.
- AC power string.
- 12 Vdc positive and negative wires.
Caution: Reconnecting the flash/sense terminal get-together wires can be risky. Exercise extreme caution when doing it. You can likewise wear a couple of safety gloves for your security.
Step 5: Turn ON the unit
From that point onward, turn ON the refrigerator indeed.
Simply press and hold the ON/OFF button until the unit reactivates.
Step 6: Short PIN 15 to the power board ground Lug
When the ice chest is ON, find PIN 15 or 16 on the power board.
Then, at that point, get one insulated jumper wire and short it to the power board ground lug
Interface one finish of the jumper wire to PIN 15.
Associate the opposite finish to the power board ground haul.
Do this for around 10 to 15 seconds.
Or on the other hand, until you hear a “tick,” which shows that the controls have been reset.
Step 7: Turn the OFF and ON the unit once
For the following step, switch the OFF and ON the cooler once.
Once more, you can do this utilizing the ON/OFF button on the display board.
Doing this is important to reboot the framework appropriately after a hard reset.
Step 8: Turn OFF the unit
You have detached a few wires before, correct?
Then, at that point, you need to reconnect them to return your ice chest once again to run.
Furthermore, to do that, you need to re-try the entire hard-reset process yet in turnaround.
The primary thing you need to do is switch OFF the refrigerator utilizing the ON/OFF button.
Step 9: Disconnect the wire(s) from the power board
When the cooler is switched OFF, disengage the wires from the power board.
Depending on your fridge’s serial number, here are the wires to disconnect:
For models with chronic number 832171 or higher:
12 Vdc positive and negative wires.
For models with chronic number 832170 or lower detach the wires in the following sequence:
- 12 Vdc positive and negative wires.
- AC power string.
- Solenoid gas valve wires.
- Flash/sense terminal gathering wires.
Step 10: Reinstall the power board cover
After disconnecting the wires, reinstall the power board cover.
Utilize a screwdriver to get the power board cover on the ice chest’s backboard.
Guarantee that the screws are accurately and firmly attached to keep away from electrical risks.
Step 11: Reconnect the wires
Also, for the last advance of the hard-reset process, reconnect the wires back to the refrigerator’s backboard.
No matter what the cooler model, here’s the request you ought to follow:
- Flash/sense cathode get-together wires.
- Solenoid gas valve wires.
- AC power rope.
- 12 Vdc positive and negative wires.
Step 12: Setup the refrigerator
At long last, set up your refrigerator.
Place the cooler in assistance by turning it ON utilizing the ON/OFF button.
Assuming that the interior temperature has been reset, change it to your ideal setting.
What’s more, you’re finished! You can now store food supplies in your Norcold refrigerator.
How to Reset Norcold Refrigerator with Magnet?
To reset your Norcold refrigerator with a magnet, follow the means underneath:
Stage One
Do not switch off the refrigerator, go outside your RV, and find the refrigerator compartment.
Stage Two
Check for a recall unit box. There will be a red LED light on it, which will make recognizing it simple. The red light ought to be lit, on the off chance that it is blazing or not lit by any means, then, at that point, this methodology won’t work.
Stage Three
If you can’t get to the unit box appropriately, delicately pull it out.
Stage Four
You will find three clasps that hold the front of the case set up. Utilize a level-edge screwdriver to eliminate the clasps and lift the front of the crate.
Stage Five
Next, check for a reed switch, this ought to be on the circuit board, simply over the LED light.
Stage Six
Touch the magnet to the reed switch, the right top precisely. Stand firm on the magnet on this footing for 5 seconds or until you hear a ticking sound.
Stage Seven
Go inside your RV and verify whether your refrigerator is done beeping or showing an error message. Sit tight for around 15 to 20 minutes so you are certain the refrigerator will keep on working appropriately.
Stage Eight
Once you are certain the refrigerator is working appropriately, go external the RV, to the refrigerator compartment. Set the front of the crate back and screw it set up with the clasps. Put the review box back in its position.
Verdict
All three methods will successfully reset your Norcold refrigerator.
We recommend trying Method 1, the Soft Reset, first.
If that doesn’t work, move on to Method 2, the Hard Reset.
If you’re still having problems after following both of those steps, try using the magnet as described in Method 3.
No matter which method you choose, always unplug your refrigerator before starting the process.